TO GO Series Titanium Manual

TO GO
LAB HEENOOR TO GO Travel Cup User Manual

WARNING — MUST BE OBSERVED
For your safety and for the proper use of this product, please read this manual carefully before use.
Please keep this manual properly for future reference.

Executive Standard
QB/T 5612 “Titanium Cup”
Cup Body Material
Pure Titanium (TA1)


Please observe the following precautions during use:

  • Do not place the product in a refrigerator, as this may cause beverage overflow or product damage.
  • Do not clean the product with metal scouring pads, steel wool, or abrasive cleaning pads, as these may physically damage the colored layer and affect the appearance of the inner and outer surfaces.
  • Do not clean the product with magic sponges containing melamine or similar materials, as harmful substances may migrate to the product.
  • Do not heat the product directly in a microwave oven, as this may cause sparks and result in injury, deformation, or product damage.
  • Do not soak the product in boiling water, as water may enter the interlayer of product components and affect product performance.
  • Do not sterilize the product by boiling. Do not use a dishwasher, dish dryer, or similar appliance for cleaning or drying, as this may cause deformation of plastic parts.
  • Do not use effervescent tablets for removing tea stains, as they may damage the product surface.
  • Do not clean the product with sodium percarbonate, active oxygen cleaners, or similar cleaning agents, as they may damage the product surface.
  • Do not fill the product with dry ice or carbonated beverages. These substances release large amounts of gas, which may increase the internal pressure of the cup body, making the lid difficult to open or causing the contents to spray out due to pressure.
  • Do not drop, collide with, knock, or strongly impact the product. Any form of heavy impact may damage the product.
  • Do not force oversized ice cubes into the product, as this may cause damage.

Declaration of Conformity

Product Materials:

  • Titanium TA1,
  • Austenitic stainless steel SUS304 (06Cr19Ni10)
  • Austenitic stainless steel SUS316L (022Cr17Ni12Mo2)
  • Polypropylene (propylene homopolymer) (PP)
  • Polyethylene (ethylene homopolymer) (PE)
  • Polymer of dimethyl terephthalate with 1,4-cyclohexanedimethanol and 2,2,4,4-tetramethyl-1,3-cyclobutanediol (PCT) (Tritan)
  • Tert-butylphenol end-capped poly(carbonate-4,4'-isopropylidenediphenyl ester) (polycarbonate) (PC)
  • Silicone rubber
  • High borosilicate glass

Declarant: Heenoor Co., Ltd.

Address: No. 1 Heenoor Road, Haimen District, Nantong, Jiangsu Province, China

Conditions of Use:

This product is intended for repeated use. The expected maximum contact temperature is 100°C. The product is intended to come into contact with aqueous foods. The expected maximum contact time is 6 hours. It shall not be used for contact with foods specially intended for infants and young children. It shall not be used for contact with foods containing more than 20% ethanol. It shall not be used for contact with turbid beverages or alcoholic beverages. Prolonged contact with acidic or alkaline foods is not recommended.

Regulatory Compliance:

- The product complies with

  • GB 4806.1 “National Food Safety Standard — General Safety Requirements for Food Contact Materials and Articles”,
  • GB 4806.5 “National Food Safety Standard — Glass Products”,
  • GB 4806.7 “National Food Safety Standard — Plastic Materials and Articles for Food Contact”,
  • GB 4806.9 “National Food Safety Standard — Metal Materials and Articles for Food Contact”,
  • GB 4806.16 “National Food Safety Standard — Silicone Rubber Materials and Articles for Food Contact”,
  • GB 9685 “National Food Safety Standard — Standard for the Use of Additives in Food Contact Materials and Articles”

as applicable to the product.

- The production process of the product complies with

GB 31603 “National Food Safety Standard — General Hygienic Practice for the Production of Food Contact Materials and Articles”.

Statement of Regulatory Compliance

The compliance of the product with the technical indicators of the above regulations is shown in the appendix.

Responsibility Statement

This declaration is issued solely with respect to the regulatory compliance of the product as a food contact material, and does not constitute a declaration of technical suitability of the product. Our company shall bear legal responsibility for the authenticity of the product samples, product information, and test reports provided, and undertakes to notify relevant parties in advance in the event of any change to the product. The product may safely come into contact with food under the declared conditions of use. The user of the product shall bear legal responsibility for the correct use of the product.

Appendix: Regulatory Limit Requirements and Compliance of Product Technical Indicators

Basic Physicochemical Indicator Compliance

Indicator Limit Compliance Source of Limit Compliance Description
(Method and Conditions for Verification)		 Required Material Parts
Overall migration, mg/dm² ≤10 Compliant GB 4806.7-2023 Test condition: 10% ethanol by volume (70°C, 2h) Plastic parts
Potassium permanganate consumption, mg/kg ≤10 Compliant GB 4806.7-2023 Test condition: distilled water (60°C, 2h) Plastic parts
Heavy metals, calculated as Pb, mg/kg ≤1 Compliant GB 4806.7-2023 Test condition: 4% acetic acid by volume (60°C, 2h) Plastic parts
Total migration of primary aromatic amines, mg/kg Not detected
(LOD = 0.01 mg/kg)		 Compliant GB 4806.7-2023 Test condition: 10% ethanol by volume (70°C, 2h) Plastic parts
Decolorization test Negative Compliant GB 4806.7-2023 Test condition: vegetable oil, ethanol, soaking solution Plastic parts
Arsenic (As), mg/kg ≤0.002 Compliant GB 4806.9-2023 Test condition: artificial tap water (70°C, 2h), followed by (40°C, 24h) Metal parts
Cadmium (Cd), mg/kg ≤0.002 Compliant GB 4806.9-2023 Test condition: artificial tap water (70°C, 2h), followed by (40°C, 24h) Metal parts
Lead (Pb), mg/kg ≤0.01 Compliant GB 4806.9-2023 Test condition: artificial tap water (70°C, 2h), followed by (40°C, 24h) Metal parts
Antimony (Sb), mg/kg ≤0.04 Compliant GB 4806.9-2023 Test condition: artificial tap water (70°C, 2h), followed by (40°C, 24h) Metal parts
Aluminum (Al), mg/kg ≤1 Compliant GB 4806.9-2023 Test condition: artificial tap water (70°C, 2h), followed by (40°C, 24h) Metal parts
Chromium (Cr), mg/kg ≤0.25 Compliant GB 4806.9-2023 Test condition: artificial tap water (70°C, 2h), followed by (40°C, 24h) Metal parts
Cobalt (Co), mg/kg ≤0.02 Compliant GB 4806.9-2023 Test condition: artificial tap water (70°C, 2h), followed by (40°C, 24h) Metal parts
Copper (Cu), mg/kg ≤4 Compliant GB 4806.9-2023 Test condition: artificial tap water (70°C, 2h), followed by (40°C, 24h) Metal parts
Manganese (Mn), mg/kg ≤2.0 Compliant GB 4806.9-2023 Test condition: artificial tap water (70°C, 2h), followed by (40°C, 24h) Metal parts
Molybdenum (Mo), mg/kg ≤0.12 Compliant GB 4806.9-2023 Test condition: artificial tap water (70°C, 2h), followed by (40°C, 24h) Metal parts
Nickel (Ni), mg/kg ≤0.14 Compliant GB 4806.9-2023 Test condition: artificial tap water (70°C, 2h), followed by (40°C, 24h) Metal parts
Tin (Sn), mg/kg ≤100 Compliant GB 4806.9-2023 Test condition: artificial tap water (70°C, 2h), followed by (40°C, 24h) Metal parts
Zinc (Zn), mg/kg ≤5 Compliant GB 4806.9-2023 Test condition: artificial tap water (70°C, 2h), followed by (40°C, 24h) Metal parts
Overall migration, mg/dm² ≤10 Compliant GB 4806.16-2025 Test condition: 10% ethanol by volume (70°C, 2h) Silicone parts
Potassium permanganate consumption, mg/kg ≤10 Compliant GB 4806.16-2025 Test condition: water (60°C, 2h) Silicone parts
Heavy metals, calculated as Pb, mg/kg ≤1 Compliant GB 4806.16-2025 Test condition: 4% acetic acid by volume (60°C, 2h) Silicone parts
Volatile matter, g/100g ≤0.5 Compliant GB 4806.16-2025 Test condition: water (200°C, 60min), followed by (200°C, 240min) Silicone parts
Lead (Pb), mg/L Small hollowware
≤1.5		 Compliant GB 4806.5-2016 Test condition: 4% acetic acid by volume (22°C, 24h) Glass parts
Cadmium (Cd), mg/L Small hollowware
≤0.5		 Compliant GB 4806.5-2016 Test condition: 4% acetic acid by volume (22°C, 24h) Glass parts

Compliance of Restricted Substance Limit Indicators

1. Compliance of Specific Migration Limit Indicators
None

2. Compliance of Residual Quantity Indicators
None

Client: Heenoor Co., Ltd.

Seller: Shanghai Heenoor Trading Co., Ltd.

Service Hotline: 400-1010-666

Manufacturer: Heenoor Co., Ltd. (Factory Code: XN-01)

Address: No. 1 Heenoor Road, Haimen District, Nantong, Jiangsu Province, China

Postal Code: 226100

Tel: +86-513-68906666

Email: mail@heenoor.com.cn